Leak Repair

Home / Product / Wrap Seal Quick Repair Kit for Pipe Leaks

Wrap Seal Quick Repair Kit for Pipe Leaks

PACKAGE:

  • 1 roll of Wrap Seal Fiberglass Tape

2″ x 5′ (50 mm x 1.2 m)
2″ x 6′ (50 mm x 1.8 m)
2″ x 12′ (50 mm x 3.6 m)
3″ x 9′ (75 mm x 2.7 m)
4″ x 12′ (100 mm x 3.6 m)

  • 1 unit of Seal Stic Quick Cure Epoxy
  • 1 pair of latex gloves
  • Operating instruction 
Download PDF

LEAK REPAIR KIT

FEATURES:

  • Repairs leak in 30 minutes
  • Applicable to pipes up to 18″ (457 mm) diameter
  • Applicable on any metal or non-metal pipes
  • Repairs T-joint, elbow joint, valve thread, valve body
  • Withstand pressure up to 400 psi (28 kg/cm2)
  • Withstand temperature up to 200 °C (392 °F)
  • Safe for drinking water and resistant to most chemicals
  • Reinforce and strengthen pipe after repair
  • Permanent repair and extend service life of pipes

APPLICABLE MATERIAL:

  • Steel
  • Copper
  • Aluminium
  • Galvanized steel
  • PVC
  • CPVC
  • Stainless steel
  • Polyethylene
  • Polypropylene
  • Cast-iron
  • Concrete
  • FRP/GRE

CHEMICAL RESISTANCE:

  • Oil
  • Water (drinking water, wastewater, steam)
  • Solvents (acetone, toluene, MEK, ethyl alcohol)
  • Mild acids (hydrochloric acid, sulfuric acid) and alkalis
  • Chemical (ethylene glycol, xylenes, ammonia)
  • Hydrocarbons
  • Bases
  • Slurries
  • Fuels (petroleum, diesels, gasoline)
  • Gases (LNG, LPG)
  • Organic salts

WORKING TIME (FIBERGLASS TAPE):

 1 minute at 30 °C (86 °F)


CURING TIME:

  • 30 minutes at 30 °C (86 °F)
  • Heat may be applied to decrease curing time
  • Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.


APPLICATION:

  • Pipe repairs
  • Offline repairs
  • Sealing joints
  • Hazardous material spill control
  • Reinforce thinning walls
  • Abrasion protection
  • Structural reinforcement
  • Repairs in hard to reach areas
  • Underwater repairs

OPERATING TEMPERATURE:

  • Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
  • Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)


OPERATING PRESSURE:

  • Recommended for pressure up to 400 psi (28 kg/cm2)
  • (Results vary depending on pipe size, type of pipe, hole size, pipe content and method of application)


APPLICABLE INDUSTRIES:

Building & Facilities

Irrigation

Manufacturing Plants

Offshore

Pharmaceutical

Wastewater

Electronics

Oil & Gas

Marine

Food Processing

Power Generation

Water Distribution

Industrial Processing

Chemical

Military

Petrochemical

Pulp & Paper

TECHNICAL DATA:

Pressure tested1/2″ (15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal withstands 4000 psi (281 kg/cm²)
1/2″ (15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal withstands 600 psi (42 kg/cm²)
Tensile strength3920 psi (276 kg/cm²)
Bond strength230 psi (16 kg/cm²)
Tensile elongation1.2 % ± 0.7 %
Compressive strength13750 ± 530 psi (967 ± 37 kg/cm²)
Yield strength2260 psi (159 kg/cm²)
Cured hardness82 Shore D
Pipe sizeNumber of rolls / size required
 50 psi (4 kg/cm2) 10 plys150 psi (11 kg/cm2) 15 plys400 psi (28 kg/cm2) 20 plys
½” (15mm)1 A1 A1 A
¾” (20mm)1 A1 A1 A
1″ (25mm)1 A1 A2 A
1¼” (32mm)1 A2 A3 A
1½” (40mm)2 A2 A1 B
2″ (50mm)1 B1 B1 B
2½” (65mm)1 B1 B2 C
3″ (80mm)1 B2 C2 C
4″ (100mm)1 B2 C3 C
Pipe sizeNumber of rolls / size required
 50 psi (4 kg/cm2) 10 plys150 psi (11 kg/cm2) 15 plys400 psi (28 kg/cm2) 20 plys
5″ (125mm)2 C2 C3 C
6″ (150mm)2 C2 C4 C
8″ (200mm)2 C3 C5 C
10″ (250mm)3 C4 C6 C
12″ (300mm)4 C5 C8 C
14″ (350mm)4 C6 C8 C
16″ (400mm)5 C7 C9 C
18″ (450mm)5 C8 C9 C
> 18″ (450mm)Contact SealXpert for recommendations

Roll size

A (2″ x 5′) (50mm x 1.2m)

A (2″ x 6′) (50mm x 1.8m)

B (2″ x 12′) (50mm x 3.6m)

B (3″ x 9′) (75mm x 2.7m)

C (4″ x 12′) (100mm x 3.6m)

WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:

  1. Stop the pipe flow
  1. Roughen the area to be repaired
  1. Knead the Seal Stic
  1. Apply the Seal Stic to fill in holes or crack of the damaged or leak area.
  1. Immerse the Wrap Seal Fiberglass Tape into water
  1. Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll
  1. Discard the plastic tube at the end of the roll
  1. Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
  1. Continue to polish the wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance