Leak Repair

Home / Product / Wrap Seal Ultra Quick Repair Kit For Active Pipe Leaks

Wrap Seal Ultra Quick Repair Kit For Active Pipe Leaks

PACKAGE:

1 roll of Wrap Seal Fiberglass Tape

2″ x 6′ (50 mm x 1.8 m)
2″ x 12′ (50 mm x 3.6 m)
3″ x 9′ (75 mm x 2.7 m)
4″ x 12′ (100 mm x 3.6 m)

1 roll of SealXpert Ultra Sealing Tape

1″ x 16′ (25 mm x 5 m)
1″ x 16′ (25 mm x 5 m)
1¼” x 16′ (32 mm x 5 m)
2″ x 16′ (50 mm x 5 m)

1 unit of Seal Stic Quick Cure Epoxy
1 pair of latex gloves
Operating instruction

ACTIVE LEAK REPAIR KIT

FEATURES:

Repairs under active leak up to 150 psi (11 kg/cm²) pressure
No shutdown required
Works on any metal or non-metal pipes
Applicable to pipes up to 18″ (457 mm) diameter
Repairs leak in 15 minutes

Withstand pressure up to 500 psi (35 kg/cm²)
Withstand temperature up to 200 °C (392 °F)
Safe for drinking water and resistant to most chemicals
Ideal for pipeline reinforcement

APPLICABLE MATERIAL:

Steel
Copper
Aluminium
Galvanized steel

PVC
CPVC
Stainless steel
Polyethylene

Polypropylene
Cast-iron
Concrete
FRP/GRE

CHEMICAL RESISTANCE:

Oil
Water (drinking water, wastewater, steam)
Solvents (acetone, toluene, MEK, ethyl alcohol)
Mild acids (hydrochloric acid, sulfuric acid) and alkalis
Chemical (ethylene glycol, xylenes, ammonia)
Hydrocarbons

Bases
Slurries
Fuels (petroleum, diesels, gasoline)
Gases (LNG, LPG)
Organic salts

WORKING TIME (FIBERGLASS TAPE):

1 minute at 30 °C (86 °F) 

CURING TIME:

30 minutes at 30 °C (86 °F)
Heat may be applied to decrease curing time
Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.

APPLICATION:

Pipe repairs
Active pipe leaks
Sealing joints
Hazardous material spill control

Reinforce thinning walls
Repairs in hard to reach areas
Underwater repairs

OPERATING TEMPERATURE:

-50 °C (-58 °F) to 200 °C (392 °F)

OPERATING PRESSURE:

Recommended for pressure up to 500 psi (35 kg/cm²)
(Result vary depending on pipe size, type of pipe, hole size, pipe content and method of application)

APPLICABLE INDUSTRIES:

TECHNICAL DATA:

Tensile strength	3920 psi (276 kg/cm²)
Bond strength	230 psi (16 kg/cm²)
Tensile elongation	1.2 % ± 0.7 %
Compressive strength	13750 ± 530 psi (967 ± 37 kg/cm²)
Yield strength	2260 psi (159 kg/cm²)
Cured hardness	82 Shore D
Dielectric strength	400 Volts/mil

Pipe size	Number of rolls / size required
	50 psi (4 kg/cm²) 10 plys	150 psi (11 kg/cm²) 15 plys	400 psi (28 kg/cm²) 20 plys
½” (15mm)	1 A	1 A	1 A
¾” (20mm)	1 A	1 A	1 A
1″ (25mm)	1 A	1 A	2 A
1¼” (32mm)	1 A	2 A	3 A
1½” (40mm)	2 A	2 A	1 B
2″ (50mm)	1 B	1 B	1 B
2½” (65mm)	1 B	1 B	2 C
3″ (80mm)	1 B	2 C	2 C
4″ (100mm)	1 B	2 C	3 C

Pipe size	Number of rolls / size required
	50 psi (4 kg/cm²) 10 plys	150 psi (11 kg/cm²) 15 plys	400 psi (28 kg/cm²) 20 plys
5″ (125mm)	2 C	2 C	3 C
6″ (150mm)	2 C	2 C	4 C
8″ (200mm)	2 C	3 C	5 C
10″ (250mm)	3 C	4 C	6 C
12″ (300mm)	4 C	5 C	8 C
14″ (350mm)	4 C	6 C	8 C
16″ (400mm)	5 C	7 C	9 C
18″ (450mm)	5 C	8 C	9 C
> 18″ (450mm)	Contact SealXpert for recommendations

Roll size

A (2″ x 5′) (50mm x 1.2m)

A (2″ x 6′) (50mm x 1.8m)

B (2″ x 12′) (50mm x 3.6m)

B (3″ x 9′) (75mm x 2.7m)

C (4″ x 12′) (100mm x 3.6m)

WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:

Minimize the flow rate and reduce system pressure

Roughen the area to be repaired

Knead the Seal Stic

Place the Seal Stic away from the leak location

Start wrapping the SealXpert Ultra Sealing Tape a few distances away from the leak location

Continue to wrap SealXpert Ultra Sealing Tape onto pipe while pushing the Seal Stic onto leak location

Immerse Wrap Seal Fiberglass Tape into water

Wrap the Wrap Seal Fiberglass Tape above the repair tape as tightly and evenly as possible, using the entire roll

Discard the plastic tube at the end of the roll

Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance