LEAK REPAIR KIT

WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS

FEATURES:

Repairs leak in 30 minutes Applicable to pipes up to 18″ (457 mm) diameter Applicable on any metal or non-metal pipes Repairs T-joint, elbow joint, valve thread, valve body Withstand pressure up to 400 psi (28 kg/cm2) Withstand temperature up to 200 °C (392 °F) Safe for drinking water and resistant to most chemicals Reinforce and strengthen pipe after repair Permanent repair and extend service life of pipes

APPLICABLE MATERIAL:

Steel Copper Aluminium Galvanized steel PVC CPVC

Stainless steel Polyethylene Polypropylene Cast-iron Concrete FRP/GRE

CHEMICAL RESISTANCE:

Oil Water (drinking water, wastewater, steam) Solvents (acetone, toluene, MEK, ethyl alcohol) Mild acids (hydrochloric acid, sulfuric acid) and alkalis Chemical (ethylene glycol, xylenes, ammonia) Hydrocarbons Bases Slurries Fuels (petroleum, diesels, gasoline) Gases (LNG, LPG) Organic salts

WORKING TIME (FIBERGLASS TAPE):

1 minute at 30 °C (86 °F)

CURING TIME:

  • 30 minutes at 30 °C (86 °F)
  • Heat may be applied to decrease curing time
  • Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.

APPLICATION:

  • Pipe repairs
  • offline repairs
  • sealing joints
  • hazardous material spill control
  • reinforce thinning walls
  • Abrasion protection
  • Structural reinforcement
  • Repairs in hard to reach areas
  • Underwater repairs

OPERATING TEMPERATURE:

  • Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
  • Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)

OPERATING PRESSURE:

  • Recommended for pressure up to 400 psi (28 kg/cm2)
  • (Results vary depending on pipe size, type of pipe, hole size, pipe content and method of application)

APPLICABLE INDUSTRIES:

appli 1 - Leak Repair Products (EN)Building & amp; Facilities
appli 2 - Leak Repair Products (EN)Electronics
appli 3 - Leak Repair Products (EN)Industrial Processing
appli 4 - Leak Repair Products (EN)Irrigation
appli 5 - Leak Repair Products (EN)Oil & amp; Gas
appli 6 - Leak Repair Products (EN)Chemical
appli 7 - Leak Repair Products (EN)Manufacturing Plants
appli 8 - Leak Repair Products (EN)Marine
appli 9 - Leak Repair Products (EN)Military
appli 10 - Leak Repair Products (EN)Offshore
appli 11 - Leak Repair Products (EN)Food Processing
appli 12 - Leak Repair Products (EN)Petrochemical
appli 13 - Leak Repair Products (EN)Pharmaceutical
appli 14 - Leak Repair Products (EN)Power Generation
appli 15 - Leak Repair Products (EN)Pulp & amp; Paper
appli 16 - Leak Repair Products (EN)Wastewater
appli 17 - Leak Repair Products (EN)Water Distribution
 

TECHNICAL DATA:

Pressure tested:1/2″ (15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal withstands 4000 psi (281 kg/cm2)
1/2″ (15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal withstands 600 psi (42 kg/cm2)
Tensile strength:3920 psi (276 kg/cm2)
Bond strength:230 psi (16 kg/cm2)
Tensile elongation:1.2 % ± 0.7 %
Compressive strength:13750 ± 530 psi (967 ± 37 kg/cm2)
Yield strength:2260 psi (159 kg/cm2)
Cured hardness:82 Shore D
Pipe sizeNumber of rolls / size required
50 psi (4 kg/cm2) 10 plys150 psi (11 kg/cm2) 15 plys400 psi (28 kg/cm2) 20 plys
½” (15mm)1 A1 A1 A
¾” (20mm)1 A1 A1 A
1″ (25mm)1 A1 A2 A
1¼” (32mm)1 A2 A3 A
1½” (40mm)2 A2 A1 B
2″ (50mm)1 B1 B1 B
2½” (65mm)1 B1 B2 C
3″ (80mm)1 B2 C2 C
4″ (100mm)1 B2 C3 C
Pipe sizeNumber of rolls / size required
50 psi (4 kg/cm2) 10 plys150 psi (11 kg/cm2) 15 plys400 psi (28 kg/cm2) 20 plys
5″ (125mm)2 C2 C3 C
6″ (150mm)2 C2 C4 C
8″ (200mm)2 C3 C5 C
10″ (250mm)3 C4 C6 C
12″ (300mm)4 C5 C8 C
14″ (350mm)4 C6 C8 C
16″ (400mm)5 C7 C9 C
18″ (450mm)5 C8 C9 C
> 18″ (450mm)Contact SealXpert for recommendations
Roll sizeA (2″ x 5′) (50mm x 1.2m)A (2″ x 6′) (50mm x 1.8m)B (2″ x 12′) (50mm x 3.6m)B (3″ x 9′) (75mm x 2.7m)C (4″ x 12′) (100mm x 3.6m)

WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:

1Leak Repair Pro 1 - Leak Repair Products (EN)Stop the pipe flow
2Leak Repair Pro 2 - Leak Repair Products (EN)Roughen the area to be repaired
3Leak Repair Pro 3 - Leak Repair Products (EN)Knead the Seal Stic

4Leak Repair Pro 4 - Leak Repair Products (EN)Apply the Seal Stic to fill in holes or crack of the damaged or leak area.
5Leak Repair Pro 5 - Leak Repair Products (EN)Immerse the Wrap Seal Fiberglass Tape into water
6Leak Repair Pro 6 - Leak Repair Products (EN)Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll

7Leak Repair Pro 7 - Leak Repair Products (EN)Discard the plastic tube at the end of the roll
8Leak Repair Pro 8 - Leak Repair Products (EN)Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
9Leak Repair Pro 9 - Leak Repair Products (EN)Continue to polish the wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance
 

WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS

1433 Pipe Repair Kit Wrap Seal Kit1 - Leak Repair Products (EN)

PACKAGE:

  • 1 roll of Wrap Seal Fiberglass Tape
    • 2″ x 5′ (50 mm x 1.2 m)
    • 2″ x 6′ (50 mm x 1.8 m)
    • 2″ x 12′ (50 mm x 3.6 m)
    • 3″ x 9′ (75 mm x 2.7 m)
    • 4″ x 12′ (100 mm x 3.6 m)
  • 1 unit of Seal Stic Quick Cure Epoxy
  • 1 pair of latex gloves
  • Operating instruction