LEAK REPAIR KIT

WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS

FEATURES:

Repairs leak in 30 minutes
Applicable to pipes up to 18″ (457 mm) diameter
Applicable on any metal or non-metal pipes
Repairs T-joint, elbow joint, valve thread, valve body
Withstand pressure up to 400 psi (28 kg/cm2)
Withstand temperature up to 200 °C (392 °F)
Safe for drinking water and resistant to most chemicals
Reinforce and strengthen pipe after repair
Permanent repair and extend service life of pipes

APPLICABLE MATERIAL:

Steel
Copper
Aluminium
Galvanized steel
PVC
CPVC

Stainless steel
Polyethylene
Polypropylene
Cast-iron
Concrete
FRP/GRE

CHEMICAL RESISTANCE:

Oil
Water (drinking water, wastewater, steam)
Solvents (acetone, toluene, MEK, ethyl alcohol)
Mild acids (hydrochloric acid, sulfuric acid) and alkalis
Chemical (ethylene glycol, xylenes, ammonia)
Hydrocarbons
Bases
Slurries
Fuels (petroleum, diesels, gasoline)
Gases (LNG, LPG)
Organic salts

WORKING TIME (FIBERGLASS TAPE):

1 minute at 30 °C (86 °F)

CURING TIME:

  • 30 minutes at 30 °C (86 °F)
  • Heat may be applied to decrease curing time
  • Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.

APPLICATION:

  • Pipe repairs
  • offline repairs
  • sealing joints
  • hazardous material spill control
  • reinforce thinning walls
  • Abrasion protection
  • Structural reinforcement
  • Repairs in hard to reach areas
  • Underwater repairs

OPERATING TEMPERATURE:

  • Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
  • Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)

OPERATING PRESSURE:

  • Recommended for pressure up to 400 psi (28 kg/cm2)
  • (Results vary depending on pipe size, type of pipe, hole size, pipe content and method of application)

APPLICABLE INDUSTRIES:

Building & amp; Facilities
Electronics
Industrial Processing
Irrigation
Oil & amp; Gas
Chemical
Manufacturing Plants
Marine
Military
Offshore
Food Processing
Petrochemical
Pharmaceutical
Power Generation
Pulp & amp; Paper
Wastewater
Water Distribution
 
 
 

 

TECHNICAL DATA:

Pressure tested:1/2″ (15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal withstands 4000 psi (281 kg/cm2)
  1/2″ (15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal withstands 600 psi (42 kg/cm2)
Tensile strength:3920 psi (276 kg/cm2)
Bond strength:230 psi (16 kg/cm2)
Tensile elongation:1.2 % ± 0.7 %
Compressive strength:13750 ± 530 psi (967 ± 37 kg/cm2)
Yield strength:2260 psi (159 kg/cm2)
Cured hardness:82 Shore D
Pipe sizeNumber of rolls / size required
 50 psi (4 kg/cm2)
10 plys
150 psi (11 kg/cm2)
15 plys
400 psi (28 kg/cm2)
20 plys
½” (15mm)1 A1 A1 A
¾” (20mm)1 A1 A1 A
1″ (25mm)1 A1 A2 A
1¼” (32mm)1 A2 A3 A
1½” (40mm)2 A2 A1 B
2″ (50mm)1 B1 B1 B
2½” (65mm)1 B1 B2 C
3″ (80mm)1 B2 C2 C
4″ (100mm)1 B2 C3 C
Pipe sizeNumber of rolls / size required
 50 psi (4 kg/cm2)
10 plys
150 psi (11 kg/cm2)
15 plys
400 psi (28 kg/cm2)
20 plys
5″ (125mm)2 C2 C3 C
6″ (150mm)2 C2 C4 C
8″ (200mm)2 C3 C5 C
10″ (250mm)3 C4 C6 C
12″ (300mm)4 C5 C8 C
14″ (350mm)4 C6 C8 C
16″ (400mm)5 C7 C9 C
18″ (450mm)5 C8 C9 C
> 18″ (450mm)Contact SealXpert for recommendations
Roll sizeA
(2″ x 5′)
(50mm x 1.2m)
A
(2″ x 6′)
(50mm x 1.8m)
B
(2″ x 12′)
(50mm x 3.6m)
B
(3″ x 9′)
(75mm x 2.7m)
C
(4″ x 12′)
(100mm x 3.6m)

WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:

1
Stop the pipe flow
2
Roughen the area to be repaired
3
Knead the Seal Stic
 

4
Apply the Seal Stic to fill in holes or crack of the damaged or leak area.
5
Immerse the Wrap Seal Fiberglass Tape into water
6
Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll
 

7
Discard the plastic tube at the end of the roll
8Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
9
Continue to polish the wrap until all bubbling has stopped.
Repair completed with smooth and hard ivory appearance
 

 

WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS

Wrap Seal emergency and quick pipe repair Kit for fixing and sealing leaking oil, gas and water pipes

PACKAGE:

  • 1 roll of Wrap Seal Fiberglass Tape
    • 2″ x 5′ (50 mm x 1.2 m)
    • 2″ x 6′ (50 mm x 1.8 m)
    • 2″ x 12′ (50 mm x 3.6 m)
    • 3″ x 9′ (75 mm x 2.7 m)
    • 4″ x 12′ (100 mm x 3.6 m)
  • 1 unit of Seal Stic Quick Cure Epoxy
  • 1 pair of latex gloves
  • Operating instruction