Metal Putty

metal putty - Metal Putty
Untitled 1 - Metal Putty

SealXpert Metal Putty is a two component, ambient-temperature curing epoxy putty. The metal putty is suitable for a wide application range, convenient-to-use, non-sagging with high bond strength.

SealXpert Metal Putty consists of two components (resin & hardener) each separately packed. The resin container is slack filled to allow the addition of hardener to be mixed with resin. It is critical to mix the metal putties thoroughly and in proper ratio to achieve the performance of the material. Whenever possible, the complete container should be mixed at one time. If the material is to be mixed in separate batches, the user must be careful to adhere to the mixing ratios specified on the product label.

The material is mixed by adding hardener to resin. The mixing process is complete when the product is free from streaks or other variances. Failure to thoroughly mix the material will cause soft spots or overall failure of the product. The mixing process should take at least 3 to 5 minutes.

When mixing large masses of metal putties (more than 500 grams), place both the resin & hardener into a clean disposable container. Mix and knead material with a putty knife or other flat tool until the product is thoroughly mixed. Do not fold material into the mix as this process can cause air entrapment that will weaken the cured product.

When applying SealXpert Metal Putty at higher temperature and mixing more quantities of each component, it will shorter the pot life. On the contrary, lower temperature and mixing less of each component will length the pot life. In the case of temperature below 10°C, it is recommended to preheat the repair surface. A fast cure may be obtained by heating with infra-red bulbs, heating pads, electric heater or open flame held close to the repair area. Any type of extra heat will increase the curing speed. In the case high temperature, reduce the mixture of each component to shorten curing time.

The pot life or working life of SealXpert Metal Putty may be extended by pouring the contents into large surface area shallow container. The pot life can also be extended when putting the shallow container on ice or in cold water.

The viscosity of SealXpert Metal Putty increases with lower temperature and decreases with higher temperature. To change viscosity in cool weather, warm the product slightly; to reduce the viscosity in hot weather, cool the product slightly.

SealXpert Metal Putty can be machined after cured and it has good corrosion and chemical resistance.

SealXpert™ metal putty is a high performance metal-filled epoxy putty. They are the best choice for repairing holes, cracks and defects. SealXpert™ metal epoxy putty is quick-curing and cost-effective in returning worn-off parts or equipment back to service.

SealXpert Metal Putty Variants

PS102 Steel Repair Metal Putty (A)

  • Metal-filled two component epoxy metal putty
  • Bonds to most metals, concrete and some plastics
  • Cures at room temperature
  • Can be drilled, tapped, machined or painted
  • Excellent resistance to oil, gasoline, water and chemicals
  • Ideal for patching and repairing areas where welding or brazing is undesirable or impossible

PS103 Aluminium Repair Metal Putty

  • Aluminium-filled two-component epoxy metal putty
  • Repairs to non-rusting aluminium castings, machinery and equipment
  • Excellent resistance to chlofluorocarbons
  • Bonds to aluminium and other metals
  • Fills porosity in aluminium castings
  • Can be drilled, tapped, machined or painted

PS104 Bronze Repair Metal Putty

  • Bronze-filled two-component epoxy metal putty.
  • Repairs to bronze and brass bushings, shafts, castings and parts
  • Repairs and rebuilds area where brazing is undesirable or impossible
  • Bonds securely to bronze alloys, brass, copper and ferrous metals
  • Can be drilled, tapped, machined or painted
Metal Putty Singapore - Metal Putty

PS105 Stainless Steel Repair Metal Putty

  • Stainless steel-filled two-component epoxy metal putty
  • Patch, repair and rebuild stainless steel parts and equipment
  • Bonds to ferrous and non-ferrous metals
  • Non-rusting

PS106 Underwater Repair Metal Putty

  • Ceramic-based two-component epoxy metal putty
  • Suitable for moist and wet conditions
  • Excellent resistance to oil and chemicals
  • Bonds to metallic and non-metallic surfaces
  • Fills porosity and cracks on valves and pump bodies
  • Can be drilled, tapped, machined or painted

PS107 5 Min (SF) Repair Metal Putty

  • Fast-curing
  • Stainless steel-filled two-component metal epoxy putty
  • Suitable for quick and emergency repairs
  • Cures in less than one hour
  • Can be drilled, tapped, machined or painted

PS108 Hi-Temp Repair Metal Putty

  • Withstands high temperature up to 230 °C (446 °F) (continuous) and 280 °C (536 °F) (intermittent)
  • Nickel alloy-filled two-component epoxy metal putty
  • Suitable for engine parts repairs
  • Can be drilled, tapped, machined or painted
SealXpert Metal Putty - Metal Putty

PS109 Supermetal Epoxy Metal Putty

  • Alloy and ceramic filled two-component epoxy metal putty
  • Excellent hardness
  • Cold welding repairing material
  • Versatile durable repair composite
  • Outstanding adhesion to all metals
  • Excellent corrosion resistance
  • Superior chemical resistance
  • Can be drilled, tapped, machined or painted

PS110 Titanium Repair Metal Putty

  • Titanium filled two-component epoxy metal putty
  • High performance
  • Excellent chemical resistance
  • Withstands heavy loads in harsh chemical environments
  • Can be drilled, tapped, machined or painted

WR204 Wear Resistant Coating

  • Ceramic microsphere and silicon alloy filled two-component epoxy coating
  • Suitable for application on vertical surfaces
  • Coating has strong adhesion and excellent properties of wear and impact resistance
Metal Putty - Metal Putty

WR211 Corrosion Resistant Coating

  • Composed of modified epoxy, wear resistant ceramic and crystal mineral powder
  • Thixotropic viscosity, suitable for application on vertical surface
  • Excellent resistance to strong alkali and acid
 

Apart from our container metal repair putty , SealXpert stocks up epoxy sticks for metals. Our aluminium, bronze, and steel epoxy are also available for your needs.